An inflatable pool is a genius idea to beat the heat. Inflatable pools are all durable and easy to set up. but it depends on two things

How to find a leak in an inflatable pool

How to find a leak in an inflatable pool

It is very easy to fix a leak in an inflatable pool. But sometimes it’s very difficult to find the leak. In place of throwing the whole item of your inflatable pool and buying new, you can simply find the leak and repair it. And It will save some of your money. Now, you can raise a question on How to find a leak in an inflatable pool. We have shared detailed information about How to find a leak in an inflatable pool and the process of fixing it.

Inflatable pool

An inflatable pool is a genius idea to beat the heat. Inflatable pools are all durable and easy to set up. but it depends on two things. They are-

  • Space
  • Capacity

How to find a leak in an inflatable pool

To Find a leak in your inflatable pool, you can use a spray bottle, dish soap, water, a soft cloth and a soft-tip marker. For doing this process, you need the time depending on the size of your pool.

Three are some steps to find leaks in an inflatable pool. They are: –

  • Make a soap mixture
  • Spread the soap Mixture Over surface
  • Mark the areas with marker
  • Re-check and Re-Examine

Make a soap mixture

First of all, you have to mix dish soap with lukewarm water. Do it until the resulting mixture is sudsy and soapy.  Then you have to Shake the bottle to mix it and ensure it is soapy enough.

Spread the soap Mixture Over surface

Start with the area that you think may be the cause of the leak. Then you have to spray the soap mixture directly onto the inflated pool’s surface.

Now Use a cloth to rub the mixture in thoroughly. Do it section by section, on the surface of the pool with the mixture. Now you have to Check the seams, around the valve, and over the entire surface.

Mark the areas with marker

Now take note of any bubbles that continue to inflate. You have to circle these areas with the marker then continue doing it because there may be more than one leak.

Re-check and Re-Examine

Check the insides, sides, and bottom of the pool. Now you can find where the leaks are forming. Finally, go back to the marked areas and re-examine them before covering the holes with a patch.

The Process of Fixing the leak

We have discussed your question which is “How to find a leak in an inflatable pool”. Now its time to know the process of fixing the leak of a inflatable pool.

Your beautiful summer day will be wasted when your inflatable begins to deflate. But don’t worry about that — you don’t have to buy a new float every time, when this happens. Instead of throwing the whole item of your pool, you can extend the life of your float with a cheap, easy and sustainable option, which is repairing the leak of your pool.

An inflatable pool holes can easily be identified and fixed with some simple steps. But to do that you need the right tools. And it will be possible if your inflatables will be as good as new. Read these directions to learn how easy this is to do at home.

You have to maintain those to fix the leak. Here they are:-

  • Find the hole of inflatable pool
  • Right Tools which you need
  •  Patch the Leak of inflatable pool

Find the hole of inflatable pool

After finding the source of the leak, cover it with a piece of tape or make a small mark over it. It is very important because it can be used easily to identify the leak when it’s time to make the repair. Before you begin patching it up, you need to confirm that it is completely dry.

Right Tools which you need

Before Repairing the leak, you will need to have the right patching tools on hand. So, you have to purchase a repair kit, but some inflatables come with a patch. Choose sealant, but you have to make sure that it’s flexible, strong and waterproof.

You will need duct tape to seal the hole, if you don’t use a patch. But The most important thing is that you have to keep in mind that if the leak is on the seam of the inflatable, then duct tape and patches will not work due to the position.

Patch the Leak of inflatable pool

Now you have found the leak of your inflatable pool and you’ve all the tools which tools you’re going to use to fix it, then it’s time to patch up the hole.

Find the spot that you previously marked. Apply sealant to the area. You need to make sure that the piece of patch or duct tape is large enough to cover the surface area around the hole. Now, cover carefully the hole with your patch or piece of duct tape.

To know in detail about the process of doing it, please read the full Article.

How to Patch an Inflatable Pool

For doing this process it is required that you have all the tools in your hand. Like Repair glue and Patch Kit for Inflatable Pools etc. If you have a large inflatable pool where the hole is in the side liner, then you will need the Pool Patch Wet Kit which is made for the liner material. It can be applied while the water is still in the pool.

Follow this process step by step

  • Dry the Surface Area
  • Cut the Patch in Right Way
  • Clean the Patch Area
  • Inflate The whole Pool
  • Apply the Glue
  • Apply the Patch onto the leak 

Go over each of these steps in more detail…

Dry the Surface Area

Completely drain all the water out of the inflatable pool.it is very important to dry the surface because the patch will hold up and be much more permanent if it is applied to a dry surface. Empty the pool before working on it.

Larger pools face some problems, but It is not a problem for medium or small inflatable pools.

The inflatable ring is usually above the water line in the larger pools. For this case, you have to dry the area very carefully. you will not need to drain the water, if you want to patch a large inflatable pool sidewall liner.

Cut the Patch in Right Way

You have to cut rounded edges on each corner if you are using a square patch. Don’t cut Sharp or angled edges, as they don’t hold up over time. Actually, after just a couple months, they tend to peel and pull up. You have to cut the patch very carefully so that it can contact the pool material on each side of the hole.

Clean the Patch Area

It is very important to dry the surface where the patch will be applied. You have to clean the surface with a sanitizing cleaner. like rubbing alcohol. You have to make sure that there is no debris or dirt. If there is any debris or dirt between the patch and the pool material, the patch can’t hold up.

Inflate The whole Pool

Now, you have to inflate the pool. Do it before applying the glue and patch. For doing this it will be a lot easier to get a good seal.

Apply the patch deflated and then inflate it again. Now, the patch could stretch and pull off easily.

Apply the Glue

After doing all the process, now you need to apply the plastic glue or repair glue to the torn area on the inflatable. Also apply the plastic glue to the back of the patch area that will be pressed onto the pool. You just need a thin layer to do the work, don’t gob the glue on there.

Apply the Patch onto the leak

Finally, Apply the patch onto the leak of the inflatable pool. Continue to apply pressure in the recommended amount of time, which is needed for the patch kit. After I apply it, now add some more plastic glue around the outside of the patch. Because it will help make a more permanent patch fix.

FAQ on an inflatable pool-

Which one is the best intex inflatable pool or Bestway inflatable pool?

Bestway pipes are oval shaped. On the other hand, Intex pipes are round shaped. Intex inflatable pool pumps are long-lasting. Easily you can use it for two seasons. Though Bestway pumps perform as well as Intex. But Intex inflatable pools are easier to set up and a bit stronger than Bestway Pools.

How to fix inflatable pool ring?

First of all, you need an air compressor. Use it, overfill the top ring, until the ring feels hard to the touch.

Now, spray the ring with a soapy water mixture. Now check by rubbing your hand over the ring to be sure that it is spread to the inside of the ring as well as the underside.

If you find any soapy bubbles on the ring, then it indicates an air leak. Now take a paper towel. Wipe the bubbles off with a bit. Now circle the leak using a permanent marker. walk around the ring looking for bubbles. If you find any then repeat this process.

Open the air valve of the ring. After that release excess air. Clean the marked areas with rubbing alcohol.

Now, you have to cut rounded edges on each corner if you are using a square patch. Don’t cut Sharp or angled edges, as they don’t hold up over time. You have to cut the patch very carefully so that it can contact the pool material on each side of the hole. Apply the glue to the patch. Be sure to cover the whole surface area.

Press the patch to the leak using firm pressure. Continue to apply pressure in the recommended amount of time. Finally, Inflate the pool ring to the required firmness.

How to patch inflatable pool?

If you have found the leak of your inflatable pool and you’ve all the tools which you are going to use to repair it, then it’s time to patch up the hole of your pool.

Find the spot that you previously marked. Apply sealant to the area. You need to make sure that the piece of patch or duct tape is large enough to cover the surface area around the hole. Now, cover carefully the hole with your patch or piece of duct tape.

How to find a leak in pool ?

Three are some steps to detect leaks in pools. They are: –

  • Make a soap mixture
  • Spread the soap Mixture Over the surface
  • Mark the areas with a marker
  • Re-check and Re-Examine

Please read our full article to know it in detail.

What is inflatable pool patch?

inflatable pool patch is used in inflatable pools when it gets leaks. If you have found the leak of your inflatable pool and you’ve all the tools which tools, you’re going to use to repair it, then it’s time to patch up the pool hole.

Find the spot that you previously marked. Apply sealant to the area of the pool. You need to make sure that the piece of patch or duct tape is large enough to cover the surface area around the hole of your pool. Now, cover carefully the hole with your patch or piece of duct tape.

We have discussed How to find a leak in an inflatable pool. We have also discussed the Fixing process of the leak of an inflatable pool. Go through the details to know How to find a leak in an inflatable pool. You must pay attention when you will try to detect the pool leak of an inflatable pool. Because it’s the most important to detect pool leak to fix it. After finding the leak you can repair the pool leak by the process that we discussed earlier. We have also discussed some FAQ about the inflatable pool to give you some appropriate knowledge about the pool

Leave a Comment

Your email address will not be published. Required fields are marked *